Transactions of Nonferrous Metals Society of China The Chinese Journal of Nonferrous Metals

您目前所在的位置:首页 - 期刊简介 - 详细页面

中国有色金属学报

ZHONGGUO YOUSEJINSHU XUEBAO

第27卷    第9期    总第222期    2017年9月

[PDF全文下载]        

    

文章编号:1004-0609(2017)-09-1902-07
Mn对生物医用Ti-Mo合金组织与力学性能的影响
武晓峰,杨会齐,王春雨

(辽宁工业大学 材料科学与工程学院,锦州 121001)

摘 要: 采用非自耗真空电弧炉制备Ti-8Mo-xMn系列合金,以考察Mn的添加对生物医用Ti-Mo合金显微组织与力学性能的影响。结果表明:两元Ti-Mo合金主要由细小的针状α″马氏体相组成,加入1%Mn(质量分数)后,等轴晶的β相大部被保留;当Mn的加入量达到3%后,β相全部被保留到室温。拉伸力学测试发现:β相不稳定的Ti-8Mo-1Mn合金在拉伸过程中发生应力诱导的从β相到α″相的马氏体转变,呈现出“双屈服”现象。加入少量Mn(1%和3%)提高合金塑性,伸长率由35%最大提高到53%。Mn量增加到5%、7%后,合金强度得到大幅提高,抗拉强度最大由856 MPa提高到1201 MPa,同时伸长率为22%。所有含Mn合金的显微硬度都较高,最高为386HV,是两元Ti-Mo合金的(251HV)1.65倍。含ω相的Ti-8Mo-1Mn合金的弹性模量最高,达150 GPa。其它含Mn合金的弹性模量在76~87 GPa之间,与人骨骼的接近,有潜力成为生物医用材料。

 

关键字: Ti-Mo合金;锰;显微组织;力学性能;生物材料

Effect of manganese addition on microstructure and mechanical properties of Ti-Mo Biomedical alloys
WU Xiao-feng, YANG Hui-qi, WANG Chun-yu

School of Materials Science and Engineering, Liaoning University of Technology, Jinzhou 121001, China

Abstract:A series of Ti-8Mo-xMn alloys were fabricated by nonconsumable electrode vacuum arc furnace, the effect of Mn addition on the structure and mechanical properties of the alloy was investigated. The results indicate that α″ phase-dominated binary Ti-Mo alloy exhibits a fine, acicular martensitic structure. When 1% Mn (mass fraction) is added, most of equiaxed β phase structure is retained. With Mn content increasing to 3% (mass fraction), entire β phase is retained. Mn alloy with instability β phase exhibits the two-stage yielding from stress-strain curves due to the stress-induced martensite transformation from β to α″ during tensile deformation. Addition of a small amount of Mn (1% and 3 %) improves the plasticity of alloys, and the elongation increases from 35% to 53%. With Mn content increasing to 5% and 7% (mass fraction), the strength dramatically improves and tensile strength increases from 854 MPa to 1201 MPa, companied with 22% elongation. All the alloys with Mn exhibits the high microhardness, the highest is 386HV,which is 1.65 times than that of binary Ti-Mo alloy. The elastic modulus of Ti-8Mo-1Mn alloy with ω phase is the highest of all alloys 150 GPa. The elastic modulus of the other alloys with Mn are about 76~87 GPa, close to those of human skeletons. These alloys seem to have a great potential for use as an implant material.

 

Key words: Ti-Mo alloy; manganese; microstructure; mechanical property; biomaterial

ISSN 1004-0609
CN 43-1238/TG
CODEN: ZYJXFK

ISSN 1003-6326
CN 43-1239/TG
CODEN: TNMCEW

主管:中国科学技术协会 主办:中国有色金属学会 承办:中南大学
湘ICP备09001153号 版权所有:《中国有色金属学报》编辑部
------------------------------------------------------------------------------------------
地 址:湖南省长沙市岳麓山中南大学内 邮编:410083
电 话:0731-88876765,88877197,88830410   传真:0731-88877197   电子邮箱:f_ysxb@163.com