Transactions of Nonferrous Metals Society of China The Chinese Journal of Nonferrous Metals

您目前所在的位置:首页 - 期刊简介 - 详细页面

中国有色金属学报

ZHONGGUO YOUSEJINSHU XUEBAO

第29卷    第10期    总第247期    2019年10月

[PDF全文下载]        

    

文章编号:1004-0609(2019)-10-2312-09
SPS烧结温度对NiTi/表面多孔Ti梯度合金组织和性能的影响
邓 霞1, 2,何远怀1, 2,焦美琪1, 2,张玉勤1, 2, 3,蒋业华1, 2

(1. 昆明理工大学 材料科学与工程学院,昆明 650093;
2. 金属先进凝固成形及装备技术国家地方联合工程实验室,昆明 650093;
3. 云南省钛材应用产品工程技术研究中心,楚雄 651209
)

摘 要: 利用放电等离子烧结技术制备NiTi/表面多孔Ti梯度合金,研究不同烧结温度对梯度合金微观组织、表面孔隙特征、力学性能及体外生物活性的影响及机理。结果表明:随着烧结温度的升高,梯度合金组织由NiTi、α-Ti、Ni、Ti2Ni、Ni3Ti混合相逐渐转变为单一NiTi和α-Ti相,内外层界面形成良好冶金结合,表面孔隙率和平均孔径呈缓慢减小趋势;同时抗压强度值快速增大而弹性模量值变化不大;1000 ℃制备的梯度合金不仅具有良好的表面孔隙特征(孔隙率35.8%、平均孔径423 μm)、较高的抗压强度(632 MPa)、较低的弹性模量(9 GPa)及优异的超弹性行为(超弹性恢复应变>4%),而且体外生物活性显著提高。

 

关键字: NiTi梯度合金;烧结温度;微观组织;力学性能;体外生物活性

Effects of sintering temperatures on microstructure and properties of NiTi/surface porous Ti graded alloy by spark plasma sintering
DENG Xia1, 2, HE Yuan-huai1, 2, JIAO Mei-qi1, 2, ZHANG Yu-qin1, 2, 3, JIANG Ye-hua1, 2

1. School of Materials Science and Engineering, Kunming University of Science and Technology, Kunming 650093, China;
2. National-local Joint Engineering Laboratory of Metal Advanced Solidification Forming and Equipment Technology, Kunming 650093, China;
3. Engineering Technology Research Center of Titanium Products and Application of Yunnan Province, Chuxiong 651209, China

Abstract:NiTi/Surface porous Ti gradient alloys were prepared by spark plasma sintering (SPS) technology. The effects and mechanism of different sintering temperatures on the microstructure, surface pore characteristics, mechanical properties and in vitro biological activity of the gradient alloys were investigated. The results show that the gradient alloys are consisted of NiTi, α-Ti, Ni, Ti2Ni, Ni3Ti mixed phase and gradually transforms into NiTi and α-Ti phase with the increase of sintering temperatures. Furthermore, a stable metallurgical bonding on the internal and external interface of the alloys could be observed. Meanwhile, the porosity and average pore size of surface porous layer is in a slowly decreasing trend. As a result, the compressive strength of the alloys increases significantly, but the compressive elastic modulus of the alloys changes less. Gradient alloy sintered at 1000 ℃ not only exhibits good surface pore characteristics (35.8% porosity as well as 423 μm average pore size), higher compressive strength (632 MPa), lower the compressive elastic modulus (9 GPa) and excellent superelastic recovery strain (>4%), but also shows good in vitro biological activity.

 

Key words: NiTi gradient alloy; sintering temperatures; microstructure; mechanical properties; in vitro biological activity

ISSN 1004-0609
CN 43-1238/TG
CODEN: ZYJXFK

ISSN 1003-6326
CN 43-1239/TG
CODEN: TNMCEW

主管:中国科学技术协会 主办:中国有色金属学会 承办:中南大学
湘ICP备09001153号 版权所有:《中国有色金属学报》编辑部
------------------------------------------------------------------------------------------
地 址:湖南省长沙市岳麓山中南大学内 邮编:410083
电 话:0731-88876765,88877197,88830410   传真:0731-88877197   电子邮箱:f_ysxb@163.com